Precipitation Imaging Probe (PIP)


An ideal probe for measuring rain, snow, graupel, and hail. Provides images as well as size distributions.
Optional Feature: Anti-shatter tips




  • Cloud particle research
  • Climate studies
  • Storm and hurricane research
  • Weather modification
  • Contrails and contrail-induced cirrus
  • Cloud chambers
  • Agricultural and industrial spray characterization

The PIP is suitable for fixed site, mobile or airborne sampling.

Photo: The PIP (behind an FSSP) mounted on a AC690 research aircraft flying over India. Photo by Duncan Axisa.


Anti-shatter Tips

The PIP can be purchased with special Korolev anti-shatter tips (right). Korolev tips significantly reduce the incidence of particle artifacts in the sample area.



Two optional software packages are available  for PIP users. The Particle Analysis and Display System (PADS) allows for instrument control and real-time data display.

The second software package, the Optical Array Shadow Imaging Software (OASIS), facilitates post-processing particle analysis. More information about these two packages is given below.


Particle Analysis and Display System (PADS)

PADS displays a user-friendly virtual instrument panel that enables the user to do the following tasks:

  • Start data recording and sampling
  • View real-time particle image data 
  • View particle volume and number concentrations, as well as Median Volume Diameter (MVD) and Effective Diameter (ED)
  • View LWC as calculated by the PIP
  • Monitor instrument parameters like PIP laser current and various electronics voltages
  • Play back data for post-flight viewing

Online PIP Software Manual



Optical Array Shadow Imaging Software (OASIS)

OASIS, shown at right, is designed for rigorous post-processing analysis. It provides additional particle statistics beyond those generated by PADS. In addition, OASIS allows users to filter particles by various criteria, including particle area, particle shape, area fraction, and inter-arrival time. Written in IGOR Pro, OASIS leverages IGOR’s robust statistical analysis features for enhanced data analysis and graphing capability. 


How it Works

Shadow images of particles passing through a collimated laser beam are projected onto a linear array of 64 photodetectors. The presence of a particle is registered by a change in the light level on each diode. The registered changes in the photodetectors are stored at a rate consistent with probe velocity and the instrument’s size resolution. Particle images are reconstructed from individual “slices,” where a slice is the state of the 64-element linear array at a given moment in time. A slice must be stored at each time interval that the particle advances through the beam a distance equal to the resolution of the probe.  Optional grayscale imaging gives three levels of shadow recording on each photodetector, allowing more detailed information on the particles.

See the PIP Operator Manual for more details.



Parameter Specification
Technique Optical Array Probe with 64 elements: 62 sizing elements, end diode rejection
Measured Particle Size Range 100 µm – 6.2 mm  
Sample Area 260 mm x 6.2 mm for standard configuration (no Korolev tips)
Upper Concentration Range 100 particles/cm3
Air Speed Range 10 – 200 m/sec 
Number of Size Bins 62
Sampling Frequency Asynchronous, 0.1 - 10 Hz. 1-second sampling is typical
Laser 660 nm
Calibration Verification Spinning glass disk with opaque dots of known size
Data System Interface: Two channels: RS-422: 56,000 Baud Rate; High-Speed Serial: 4 x 106 Baud Rate (RS-422 only)
Software (Optional) Particle Analysis and Display System (PADS) 
Optical Array Shadow Imaging Software (OASIS) 
Weight 21 lbs./9.5 kg in DMT canister
10.5 lbs./4.8 kg outside of canister
25 lbs/11.4 kg with generic canister
Power Requirements 28VDC 3A for System Power
28VDC and 9A for Anti-ice Power
Optional AC voltages for system power and anti-ice heaters
Environmental Operating Conditions Temperature: -40 °C to +40°C  
RH: 0 – 100%, non-condensing
Altitude: 0 - 50,000 ft / 0 - 15 km
Routine Maintenance DMT recommends conducting basic instrument performance checks and inspecting the PIP optical windows before a flight. A weekly calibration check is also recommended. 

Specifications are subject to change without notice.


Included Items

  • Instrument
  • Shipping case
  • Operator manual
  • One-year warranty
  • Spinning disk for calibration check (pictured)
  • One day of training at DMT’s facility

Accessories (Purchased separately)

  • Laptop and Particle Analysis and Display System (PADS) software
  • OASIS Software
  • Data Acquisition System


How to Order

Contact DMT for pricing or more information.


Phone: +001 303 440 5576
Fax: +001 303 440 1965